Is your Maytag washer control panel annoying you and not working? Do not worry! This issue is quite common in these washers and you can solve them on your own.
Here are a few causes that might be making your Maytag washer’s control panel unresponsive.
So, continue reading this article to find out how you can solve these issues.
Why Is The Maytag Washer Control Panel Not Working?
Part Failure
The first thing that you should check whenever your control panel stops working is to see if it is caused by a defective part.
Modern washers such as Maytag washers are more complicated that the previous washers and there are chances that one of the parts in your washer is broken and the machine’s control panel is stuck due to it.
So, check the parts of the washer and if all of them are intact then move further.
Malfunctioning Timer
The washer’s timer is the part which tells your machine the time of cycle and when to perform a specific action such as washing, draining, spinning, etc.
If the washer timer is broken then it can affect many parts of the washer including the control panel. It might stop the washer mid-cycle or skip a complete cycle during the wash.
This can jam the control panel and make it stop working as it might not get the accurate signals.
So, to check the timer, you should place a multimeter and see if the time is working properly or not. If not, then either get it replaced or repaired.
Faulty Display Board
The display board in your washer contains a whole circuit board which is connected with the main control panel and display board of your washer.
When you use the board you press on the washer’s buttons and they send that input to the control panel and display it on the screen.
If you press the wash cycle and the display board shows a spin cycle then there might be an issue with the display board. So, inspect it and get it repaired or replaced.
Failed Control Board
If you have placed your washer in a really heated area or in a lot of moisture or if there is any manufacturing defect then it can fail the board.
So, if the control board has failed then all or some of the buttons of your control panel will stop working.
So, first check the power supply and if it is fine then the control board has failed. So, get is replaced as soon as possible.
Malfunctioning Main Control Board
The main control board also known as the circuit board of your washer is the part of your washer which connects all the Maytag washer’s parts with the control board.
This makes your washer perform all the cycles and functions. So, if one of your functions in the washer is not working then the control board might have malfunctioned or failed.
Though this problem is not common so if you face this issue then you should call a professional technician to replace the main control board for you.
Line Fuse Problem
There are different fuses in a washer and the same is the case with the Maytag washer.
One of these fuses is the line fuse which prevents the internal circuit of the washer from getting overloaded with the current.
If the current supply from the main power supply unit exceeds its normal limit then this fuse can blow.
You can check the fuse by testing it for continuity and if there is no continuity then you will have to install a new fuse in your washer.
Thermal Fuse Issue
Just like line fuse there is a thermal fuse in the Maytag washer which is responsible for controlling the heating-up of the washer.
If your washer starts getting heated a lot then this fuse blows out and stops the machine from overheating.
This will prevent your washer from getting damaged and your washer will not start or work if this fuse has blown.
So, check this fuse and replace it, if you want your control panel and washer to start working again. Simply, use a multimeter to check this fuse and then solve the problem.
Power Supply Problems
If you are inputting commands in your Maytag washer’s control panel by pressing the buttons but it is not working then the power supply might be the culprit.
If your washer is not receiving any power then the control panel might not respond. So check the outlet socket where the washer is plugged in.
If there are no issues then check the washer’s power cord. Use a multimeter to check if there is current and the cord is fine or not.
If you find any issues with the socket or the cord, replace them so the control panel can start working again.
Filling or Drainage Issues
If you are attempting to start your washer but the control panel won’t work and is stuck on LF or F8E1 error codes then this indicates that your washer has issues with the water filling.
So, my friend if you are seeing this code then you must check the inlet and outlet hoses of your washer. If your washer is draining slowly or filling and draining simultaneously then you will see these codes.
So, check these hoses and make sure that they are fitted properly and the valves for hot and cold water are turned on fully.
If not then adjust them and see if the error disappears. Also, if there are any damages, splits or leaks in the inlet or outlet hose then you should get them replaced as well.
Final Words
A Maytag washer’s control panel not working can be really annoying when its panel is not working.
So, the best thing you can do is check the washer for any broken part, electrical glitches and other drainage or filling issues.
If you find any then you can resolve them on your own. However, if you are facing any difficulties or are unable to resolve the issue then you must contact an expert so they can troubleshoot your washer for you.
FAQs
How can you reset a Maytag washer control panel?
You should first find the knits or delicates option on your display panel of the washer.
You will possibly find this mode in the washing options menu of your display panel and then keep pressing this button for five seconds.
After this your Maytag washer’s display will start blinking and flashing showing the error codes being eliminated then the washer has been reset.
Why is my control panel touchpad not working on my Maytag washing machine?
There can be many reasons why your Maytag washer’s control panel touchpad is not working like lack of power reaching your washer, a blown fuse or plug or possibly a malfunctioning door handle.
Get it checked to find out the exact problem.
Why did my Maytag washer’s control panel touchpad stop working suddenly?
The simple answer is that your touchpad’s driver might need an update or it might be missing.
So, try updating the driver software or reinstalling it to solve this issue or if the issue persists then check other problems.
You may like to read!
GE Top Load Washer Button Not Working